TROLLEYS

• The CHVX enables any type of hoisting device to be hung.
• Variable travel movement speed 5 to 20 m/min.
• Gap between flanges adjustable enabling it to be adapted to all types of IPN, IPE, HEA or HEB straight or curved profiles.
• Protection is IP66 in standard.
• Class F motor protection system.
• 4 rubber stops.
• Trolley delivered non assembled.
• Low voltage electrical cabinet.

• Worm gear box to obtain reduced sidedimension (5 or 10 m/min and 10-2.5 m/min).
• Dual travel speed 20 & 5 m/min (contactor control).
• Additional hand chain for hand driven trolley.
• Travelling limit switch with different setting.
• Special power supply, special control voltages.
• Control pendant with 2,5 m cable.
• Additional meter pendant control cable.
• 4-button pendant for hoist to replace standard 2-button pendant.
• Rain cover.
• Counter wheels.
• Counterweights.

• Can be used with any type of overhead hooked lifting device.
• Operated by directly pushing the load (CHZD models) or using a hand wheel and chain (CHZDD models).
• Epoxy Painting (min. 50 µm).
• Easily adjustable to fit beams.
• Steel rollers machined for smooth movement.
• Trolley body made of high-resistance steel.
• Rollers compatible with all sorts of I and H beams.
• Wheel ball bearings are moisture-tight and maintenance free.
• Galvanized hand chain on CHZDD type.
• Loads up to 100 tons.
• Delivered with CE certificate.

• Greater load capacities available on request
• 3 Type «Y» models with 3 lifting points, or type “X” with 4 lifting points are also available on request
• Lifting beams for big bag
• Special lifting beams
• Galvanized lifting beams
• Special lifting beams with pick-up fork for pallets

The ideal solution for hand-operated articulated sliding girders with spans of up to 8 metres. The PRD offers a low-cost solution for moving loads of 250 to 2.000 kg by pushing them along any type of monorail type steel section.

The ideal partner for this articulated rolling beam is a handpowered chain hoist.
The PRD trolley kit consists of :

• A pair of trolleys each fitted with four steel rollers (mounted on ball bearings).
• 4 anti-drop rollers (in compliance with legislation).
• A coupling consisting of a strap piece in die-stamped steel and 2 articulations, one of which is mounted on a ball and socket joint.
• The assembly boltwork.
• Assembly documentation.

The ideal solution for electrically-powered articulated sliding girders with spans of up to 12 meters. The PRV offers a low-cost solution for powered shifting of loads of 250 to 2.000kg along any type of monorail type steel section.

The ideal equipment for this articulated travelling beam is an electrically-powered chain hoist.

The PRV trolley consists of the following :

• The electrical equipment for a 380V to 460V/3ph/50Hz power supply.
• A pair of electric trolleys capable of running at variable speed (5 to 20 m/mn), single speed (5 or 10 m/min) or two speeds (10/2.5 or 20/5 m/min), each equipped with 4 cast iron rollers (2 driving and 2 support rollers), mounted on ball bearings and adjustable, with gears cut and rims machined to run on all types of raceway.
• Four anti-drop rollers (in compliance with legislation).
• A coupling consisting of a strap piece in die-stamped steel and two articulations, one of which is mounted on a ball-and-socket joint.
• Two safety chains.
• The assembly bolts and fasteners.
• Documentation for assembly and installation.

• VHR hand chain block or EUROCHAIN VR electric chain hoist.
• Travelling movement box.
• Complete travelling movement electrical kit.
• Travel limit switch.
• Slow variable speed (3 to 10 m/min.).
• Other voltages (230 to 575 V).
• Execution is possible only in the case of a complete electric hoist control system (very low voltage version) and PRV type electric-powered trolley.
• This kit contains a set of pre-wired supply and control lines (accessories and boltwork), the line securing fasteners, control by a hung pendant push button box, an electrical cabinet.